How.to Make My.popsocket Sticky Again if.it Domt.have the Stick Part

Download Article

Download Article

PopSockets are very useful for getting a better grip on your telephone, but they tin can get dirty with fourth dimension and the adhesive that sticks information technology to the back of your phone can become loose and lose its stickiness. After removing information technology from your phone, simply soak it in water and scrub it with soapy h2o your PopSocket to go far look skilful equally new and stick as if you bought it yesterday.

1. 1

   Fill a shallow dish with cold tap water. Grab a shallow dish, such every bit a minor bowl or a deep plate, and make full information technology with about .5 in (1.3 cm) of very cold tap water. This is to ensure that you only soak the agglutinative side of the PopSocket — yous should make clean the plastic grip separately.

   • Even if your PopSocket is larger than normal, using only a .5 in (1.3 cm) layer of water will ensure that merely the adhesive side touches the water when it is extended.

2. ii

   Remove the popsPopSocketocket and place it sticky-side down in the water. Dig your fingernail under the PopSocket to pry it off of your phone, and so pull the plastic grip to it extend to its total length. Place the adhesive side downward in the water so the plastic grip pokes higher up the surface of the water.

   • Be certain that your extended PopSocket rises above the surface and drain out water as necessary to avoid getting the residual of it wet.^[1]

   Advertisement

3. 3

   Permit the PopSocket soak for about 10 seconds, and so remove it. Don't disturb the water and don't accept it out before ten seconds are up. Once 10 seconds take passed, quickly take it out of the h2o by the grip and shake off any backlog water. Do not let it soak for more than than 10 seconds or it could ruin the adhesive. ^[2]

   • If you are concerned about ruining the agglutinative, run the PopSocket nether cold water for a few seconds instead, although soaking it is more effective.^[3]

4. 4

   Lay a paper towel down and place the PopSocket sticky-side up. You can utilise a regular kitchen towel or a linen towel, depending on what you accept readily available. Lay the PopSocket with the sticky side pointing up and the design and plastic grip bear on the paper.^[four]

5. 5

   Let the adhesive side of the PopSocket dry for 10 minutes. Get out your PopSocket to dry for x minutes at most, and continue an eye on it equally information technology dries to run into if it finishes sooner.^[5] Avoid using a hair dryer or dabbing information technology with a towel or you lot could damage the adhesive and make information technology less glutinous. Merely permit it air dry, and swiftly re-attach it to your telephone the moment it is dry out by pressing the viscous side firmly onto the back of your phone.

   • Practise non let your PopSocket dry for more than than 15 minutes at near or information technology may lose its ability to stick.
   • If you accidentally leave information technology out, run it under common cold water for a few seconds then let information technology dry over again, although be aware that it may not regain its stickiness.

   Advert

1. 1

   Remove any additional stickers you lot've added to the end of the PopSocket. If you added stickers to the PopSocket's grip, yous will need to remove them earlier you lot clean it. If the adhesive is nonetheless good on the sticker feel free to put it dorsum on after cleaning, otherwise you will have to simply throw information technology away and find a new one.

   • Popsockets ordinarily come with some kind of design on the cease of the grip, so even if you have to remove any additional stickers you lot've added, it will still take an aesthetic design.^[6]

2. 2

   Remove the PopSocket and run the plastic grip under cold water. Apply your fingernail to pry the PopSocket off of your telephone, so hold the adhesive side of the PopSocket and plow your water faucet to a low menses on cold. Run but the plastic grip of the PopSocket under water — if you must, wrap the adhesive in a mitt towel to forbid getting it moisture and affecting its stickiness.

   • You can clean the adhesive separately, but if you get it wet before you're ready to clean it, you could cause the adhesive to lose some of its stickiness. Wrap information technology or take intendance to not get it wet while cleaning the grip.

3. 3

   Scrub the plastic grip with the corner of a soapy rag, fugitive the adhesive. Hold the PopSocket by the sticky side over again and scrub the plastic grip with the corner of a soapy rag PopSocket. Take care to avert getting soap on the adhesive, and only scrub the plastic parts of the PopSocket.

   • Scrub inside the grooves of the PopSocket's expandable middle section with a cotton swab soaked in soapy water.
   • Employ 70 percent rubbing booze to particularly stubborn stains or grime with a cotton swab, then rinse it under water again. Rubbing alcohol is great for removing stains as it evaporates quickly and leaves no harm.

4. iv

   Rinse the grip once again, so dry it with a paper towel or rag. Run the grip under water to get rid of soapy residue and rubbing alcohol, again taking care to avoid getting the adhesive wet. Then, have a dry rag or a paper towel and dab the PopSocket dry until information technology is completely free of water.^[vii] Press information technology firmly onto the dorsum of your phone with the glutinous-side downwards.

   • You can too air dry the plastic grip. Expand the PopSocket and so balance it on its side on a paper towel. This prevents the adhesive from sticking to the towel and will still allow the grip to air dry out and drip dry.

   Ad

Enquire a Question

200 characters left

Include your email address to become a message when this question is answered.

Submit

Advertisement

• After re-attaching the PopSocket to your phone, await at least 1 hr before y'all extend the grip and use it. This allows enough fourth dimension for the adhesive to fully stick to your phone, reducing the risk of it detaching suddenly.^[8]

Thanks for submitting a tip for review!

Advertizement

• Avert using rubbing alcohol in a airtight room, and have the PopSocket to a well-ventilated area to prevent inhaling rubbing alcohol fumes.

• Never allow the gummy side of the PopSocket be exposed to air for more than than xv minutes, even when cleaning the plastic grip, every bit this destroys the adhesive.

Advertisement

About This Article

Thank you to all authors for creating a folio that has been read 29,408 times.

Is this article up to engagement?

palmerints1937.blogspot.com

Source: https://www.wikihow.com/Clean-a-PopSocket

Share this post